Search results for " dynamic mechanical analysis"
showing 9 items of 9 documents
New Polylactic Acid Composites Reinforced with Artichoke Fibers
2015
In this work, artichoke fibers were used for the first time to prepare poly(lactic acid) (PLA)-based biocomposites. In particular, two PLA/artichoke composites with the same fiber loading (10% w/w) were prepared by the film-stacking method: the first one (UNID) reinforced with unidirectional long artichoke fibers, the second one (RANDOM) reinforced by randomly-oriented long artichoke fibers. Both composites were mechanically characterized in tensile mode by quasi-static and dynamic mechanical tests. The morphology of the fracture surfaces was analyzed through scanning electron microscopy (SEM). Moreover, a theoretical model, i.e., Hill's method, was used to fit the experimental Young's modu…
Thermal and Mechanical Characterization of Yarn Samples from Flemish Tapestry of the Sixteenth Century
2022
We propose a physico-chemical approach for theharacterization of the conservation condition of yarns from a Flemish tapestry of the sixteenth century. The aging effect on the yarns’ performance was evaluated by comparison with commercial materials. Water uptake experiments highlighted the aptitude of yarns toward water sorption and their increased hydrophilicity upon aging. Thermogravimetric analysis can be considered a fast approach for the fiber identification and assessment on the material life-time. The dynamic mechanical analysis provided direct evidence on the yarns, conservation state and their performance under different mechanical stresses. The proposed characterization path can be…
As the filler influences morphology, mechanical properties and thermal degradation of a polymer
2013
The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.
2022
Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could …
Morphology, mechanical properties and thermal degradation kinetics of PMMA-zirconia nanocomposites prepared by melt compounding
2012
Zirconia nanoparticles were synthesized by means of a sol-gel method and embedded in poly(methyl methacrylate) (PMMA) by melt compounding. The zirconia was well dispersed in the PMMA matrix, with only a few clusters, especially for the highest investigated zirconia content. NMR results showed heteronuclear dipolar interactions involving the carbons and the surrounding hydrogen nuclei. The effect of the amount of zirconia, in the range of 1–5!wt%, on the thermomechanical properties and thermal degradation kinetics of PMMA was also investigated by means of dynamic mechanical analysis (DMA), thermogravimetric analyses (TGA), and Fourier-transform infrared spectroscopy (FTIR). The presenc…
Static and dynamic mechanical properties of Arundo Donax fillers-epoxy composites
2014
Abstract Aim of this work is to investigate the feasibility of using a natural and inexpensive filler obtained by grinding the culms of Arundo Donax as reinforcement of epoxy resins. The effect of the content and size of Arundo Donax fillers on static and dynamic mechanical properties was evaluated showing that the composites exhibit higher tensile moduli, comparable flexural moduli and lower strength properties in comparison to the neat resin. Moreover, changes in the storage and the loss moduli only above the glass transition temperature (i.e. in the rubbery region) were found while neither significant shifts of tan δ peaks to higher temperatures nor reductions in the peak height of the c…
Mechanical, Thermomechanical and Reprocessing Behavior of Green Composites from Biodegradable Polymer and Wood Flour
2015
The rising concerns in terms of environmental protection and the search for more versatile polymer-based materials have led to an increasing interest in the use of polymer composites filled with natural organic fillers (biodegradable and/or coming from renewable resources) as a replacement for traditional mineral inorganic fillers. At the same time, the recycling of polymers is still of fundamental importance in order to optimize the utilization of available resources, reducing the environmental impact related to the life cycle of polymer-based items. Green composites from biopolymer matrix and wood flour were prepared and the investigation focused on several issues, such as the effect of r…
Bio-inspired consolidants derived from crystalline nanocellulose for decayed wood
2018
Abstract Novel bio-inspired materials derived from crystalline nanocellulose (CNC) have been tested as wood consolidants. A suspension of CNC, produced by acid hydrolysis of cellulose and used as such or mixed with lignin and/or siloxane derivatives (PDMS), was applied on rotted wood samples of Norway spruce. X-Ray diffraction analysis on CNC powder showed high crystallinity index. Dynamic light scattering (DLS) measurement indicated a nearly uniform particle size distribution with an average hydrodynamic diameter for pure CNC smaller than that in the mixtures. Raman and FTIR spectroscopies suggested interactions between lignin, PDMS and CNC components. The storage modulus of wood samples, …